6 mins read
0 Comments

Dairy Utilities Operator Job Description

Dairy Jobs, the specialist dairy job board

This Dairy Utilities Operator job description sets out the main duties, qualifications, skills and measures of success for the role, which is also known as Boiler Operator, Plant Room Operator, Services Operator or Boiler and Refrigeration Operator. Download it free as a Word or PDF template and adapt it for your own vacancy.

This template is a guide only. Adapt it to your vacancy and check it meets the employment law where the job is based before you use it. See our terms of use.

Job titleDairy Utilities Operator
Also known asBoiler Operator, Plant Room Operator, Services Operator, Boiler and Refrigeration Operator
DepartmentEngineering and site services
Reports toUtilities Engineer (or Engineering Manager)
Direct reportsNone

What does a Dairy Utilities Operator do?

Runs the steam boilers, refrigeration plant, compressed air, water treatment and hot water systems that keep a dairy site working during a shift. Does plant-room rounds, water tests and meter readings, responds to alarms, carries out basic maintenance and keeps accurate logs.

Dairy Utilities Operator duties and responsibilities

Running the boilers

  • Start up, run and shut down the steam boilers to the site procedures and hold steam pressure steady for production and CIP
  • Test boiler water and feedwater at the set times for hardness, alkalinity, TDS and treatment chemical levels, and record every result
  • Carry out bottom and surface blowdown and adjust chemical dosing on the test results to keep the boiler water within its limits
  • Check the feed tank or hot well, feed pumps, condensate return and deaeration so the boiler always has treated water
  • Test the low-water cut-offs and check safety valves, gauge glasses and burner controls as the schedule says
  • Treat any water test or check outside its limit as a failure: act on it at once, tell the Utilities Engineer and record what was done
  • Watch fuel supply, flame and flue gas readings and report anything unusual

Plant-room rounds

  • Walk the refrigeration plant room on every round and check compressor oil levels, suction and discharge pressures, temperatures and the ammonia leak detection system
  • Respond to ammonia leak alarms by following the site emergency procedure and calling the engineer; never enter a plant room in alarm to investigate
  • Check air compressors, dryers and receivers, drain condensate and keep compressed air pressure and dew point on target
  • Run the water treatment and softening plant, regenerate softeners, top up salt and check treated water hardness
  • Keep hot water, and the steam and water supply to the CIP sets, at the right temperature and pressure for production and hygiene
  • Check cooling towers, chilled water and glycol systems for leaks, noise, vibration and correct levels
  • Read gas, electricity, water and steam meters and log the readings on every shift

Alarms, faults and basic maintenance

  • Respond to alarms, find the cause, make the plant safe and call the Utilities Engineer when the fault is beyond your training or authority
  • Carry out basic maintenance such as changing filters, greasing bearings, cleaning strainers and replacing gauges
  • Report faults clearly on the maintenance system and help the technicians with repairs where trained
  • Isolate plant for maintenance under the permit to work and lock-out rules, and never bypass a safety device
  • Keep spares, chemicals and consumables for the plant rooms stocked and stored correctly
  • Flag any plant that is drifting or working harder than normal before it fails

Safety, hygiene and handover

  • Do the legionella checks on cooling towers and water systems, such as temperatures, dosing and bleed-off, and record them
  • Handle boiler and water treatment chemicals safely, using the correct PPE and the safety data sheets
  • Keep plant rooms clean, tidy, well lit and free of leaks and trip hazards
  • Give and receive a clear handover of plant status, readings, open faults and any alarms at every shift change
  • Report leaks of steam, ammonia, gas or chemicals straight away, however small
  • Keep boiler logs, water test records, meter sheets and checklists complete and accurate

Dairy Utilities Operator qualifications and experience

Essential

  • Experience operating steam boilers or industrial plant-room equipment
  • Boiler operator training or certificate, as required where the job is based
  • Good reading, writing and number skills for logs, tests and dosing calculations
  • Ability to follow written procedures and permit to work rules exactly
  • Basic practical skills with hand tools, gauges and test kits
  • Willingness to work shifts, including nights and weekends

Desirable

  • Experience with ammonia refrigeration plant and its leak alarm and emergency procedures
  • Refrigeration or ammonia handling training, as required where the job is based
  • Knowledge of boiler water treatment and the reasons behind each test
  • Experience with compressed air systems, water softeners and reverse osmosis plant
  • Legionella awareness training, as required where the job is based
  • Experience in a dairy or other food factory
  • Basic knowledge of CIP and the steam and hot water demands of a dairy
  • Mechanical or electrical apprenticeship or trade background

Skills and attributes

  • Attention to detail with readings and test results
  • Calm and methodical when alarms go off
  • Honest, accurate record keeping
  • Safety first attitude
  • Practical, hands-on approach
  • Clear communication at handover and when calling for help
  • Reliability and good timekeeping

How success is measured

  • Steam, compressed air, water, hot water and refrigeration supplied to production without interruption
  • Boiler water tests done on time, with any result outside its limit acted on at once and recorded
  • Safety devices tested on schedule with no overdue checks
  • Meter readings and plant logs complete and accurate every shift
  • No ammonia releases, boiler incidents or legionella non-conformances
  • Plant rooms clean, tidy and ready for audit
  • No accidents or injuries

Working conditions and safety

Shift work on a production site, which may include nights, weekends and 12-hour shifts. The work involves rounds through hot, noisy boiler houses and plant rooms, some time outdoors at cooling towers and tanks, handling treatment chemicals and occasional lifting; PPE and training are provided.

  • Follow health and safety rules and safe systems of work, and wear the correct PPE
  • Follow food safety, hygiene, HACCP and quality procedures at all times
  • Report hazards, accidents, near misses and concerns promptly

Dairy Utilities Operator interview questions

Use these questions to assess candidates for a Dairy Utilities Operator role. Each one includes what a good answer shows.

  1. Which boilers and plant-room equipment have you run before, and what checks did you do on a shift?
    What a good answer shows: Names real plant, such as fire-tube or water-tube boilers, ammonia or glycol chillers and air compressors, and describes regular rounds checking pressures, levels, temperatures and alarms.
  2. Why do you test boiler water, and what happens if the tests are missed?
    What a good answer shows: Explains that the tests protect against scale, corrosion and carryover, which can damage the boiler or make it unsafe, and that blowdown and dosing are adjusted on the results.
  3. A boiler water test result is outside its limit. What do you do?
    What a good answer shows: Treats any result outside the limit as a failure, however small the margin. Acts at once by following the procedure for blowdown or dosing, re-tests to confirm the correction has worked, tells the Utilities Engineer, records both results and the action taken, and never writes an out-of-limit result up as acceptable.
  4. What do you do when the low-water alarm goes off on a boiler?
    What a good answer shows: Checks the gauge glass first and does not reset the alarm or feed water in until the level is confirmed. Follows the site procedure, shuts off the burner if the water level cannot be confirmed, finds the cause and calls the engineer.
  5. How would you respond to an ammonia leak alarm in the refrigeration plant room?
    What a good answer shows: Does not go in to investigate. Follows the site emergency procedure, raises the alarm, keeps people out, isolates from outside where it is safe to do so, and calls the engineer and the emergency contacts.
  6. What is a permit to work, and when would you use one?
    What a good answer shows: Understands it is a written authorisation that sets out the isolations, hazards and controls for a job, and that it is needed before anyone works on boilers, pressure systems, refrigeration plant or in confined spaces.
  7. Why is lock-out important before working on plant?
    What a good answer shows: Understands it stops machines starting, or steam, pressure and chemicals being released, by accident, and follows it every time, even for a quick job.
  8. What legionella checks have you done on cooling towers or hot and cold water systems?
    What a good answer shows: Mentions temperature checks, dosing and bleed-off, cleaning and disinfection, keeping the log book up to date and reporting anything outside its limit at once.
  9. How do you make sure your meter readings and plant logs are accurate?
    What a good answer shows: Writes readings at the time, checks they make sense against the last shift, never guesses or fills them in later, and corrects mistakes properly without hiding the original entry.
  10. How do you give a good handover to the next shift?
    What a good answer shows: Shares plant status, alarms, test results, open faults, work in progress and any permits still live, clearly, both in person and in writing.

Hiring a Dairy Utilities Operator? Advertise your vacancy on Dairy Jobs and reach a growing network of approximately 300,000 dairy specialists worldwide, or ask our team about recruitment support. Looking for a Dairy Utilities Operator job? Browse live dairy jobs or create a free job alert. New to the role? Read our guide: How to Become a Dairy Process Operator.

Related dairy job descriptions

Frequently asked questions

What does a Dairy Utilities Operator do?

Runs the steam boilers, refrigeration plant, compressed air, water treatment and hot water systems that keep a dairy site working during a shift. Does plant-room rounds, water tests and meter readings, responds to alarms, carries out basic maintenance and keeps accurate logs.

What qualifications does a Dairy Utilities Operator need?

Employers usually look for: experience operating steam boilers or industrial plant-room equipment; boiler operator training or certificate, as required where the job is based; good reading, writing and number skills for logs, tests and dosing calculations.

Who does a Dairy Utilities Operator report to?

A Dairy Utilities Operator usually reports to the Utilities Engineer or the Engineering Manager.

Can I use this Dairy Utilities Operator job description for my own vacancy?

Yes. Download the free Word template, add your location, contract and salary details, and adapt the duties to your site. You can then advertise the role on Dairy Jobs.

© 2026 Dairy Jobs (Specialist Recruiters Ltd). You may adapt this job description for your own vacancies. Please do not republish it.

Subscribe to newsletter

Subscribe to get the latest job updates.